Important Disclaimer: This article references a model that is no longer in production. Please note that the availability of replacement parts or discussed accessories is not guaranteed.
General Questions
Where is the serial number located?
The serial number is on the ID label on the front of the stand, above the Grizzly nameplate.
How long does assembly take?
Assembly and setup typically take about 1 hour.
Where is the G1023Z manufactured?
This table saw is made in Taiwan.
What are the differences between the G1023 series table saws?
G1023S: Basic cabinet table saw with upgraded Shop Fox Classic Fence.
G1023Z: Features a rail-mounted switch, hinged motor cover, and Shop Fox fence.
G1023ZX: Same as G1023S but with a 5 HP motor.
Cutting & Blade
What is the maximum stack dado head width?
The saw arbor allows a maximum stack of 13/16".
What is the maximum width of cut to the right of the blade?
Standard rails: 25" right / 8" left
Optional long rails (G4725): up to 48" right
What is the maximum depth of cut?
At 90°: 3-1/8"
At 45°: 2-1/8"
Which way does the blade tilt?
The blade tilts to the right as you face the saw from the operator’s position.
Motor & Power
What motor does the G1023Z use?
3 HP, single-phase, 3450 RPM TEFC capacitor-start induction motor, prewired for 220V.
Are other motors available?
Yes. Grizzly carries both 3 HP and 5 HP motors for this saw.
Can I order this machine without the motor?
No. Removing the motor during manufacturing is cost-prohibitive; we suggest selling the stock motor privately if you wish to replace it.
How is power transferred to the blade?
Via a triple V-belt drive.
How many V-belts are on this machine?
Three matched V-belts.
What type of switch does it have?
Magnetic switch with thermal overload protection.
Table & Fence
What are the table dimensions?
Standard table with extension wings: 40-1/8" W × 27" D
Floor-to-table height: 34"
Main table thickness: 1-3/4"
What is the fence like?
Front and rear locking with steel face (Shop Fox Original). Length: 30" × 2" × 3-1/2".
What are the fence rails like?
Steel angle iron, 47" × 1-1/2" × 1-1/2".
Can I install an aftermarket fence?
Yes. Some aftermarket fences may require modifications to mount the rails.
Does the saw have a miter gauge?
Yes, T-slot type, 3/4" wide × 3/8" high.
Dust Collection
Does this machine have a dust port?
Yes. It has a 4" dust port.
What are the CFM requirements for a dust collector?
A dust collector should handle approximately 450 CFM for a 10" table saw. This is an average number and depends on hose length and system efficiency.
Construction & Materials
What is the table made of?
Precision-ground cast iron with cast iron wings.
What is the cabinet made of?
Pre-formed steel.
What are the trunnions made of?
Cast iron.
What is the fence made of?
Steel and cast aluminum.
What are the rails made of?
Steel angle iron.
What is the guard made of?
Steel and clear plastic.
What are the arbor bearings like?
Sealed and permanently lubricated.
Key Specifications
Blade Diameter: 10" max
Arbor Size: 5/8"
Arbor Speed: 4200 RPM
Motor: 3 HP, single-phase, 3450 RPM
Power Transfer: Triple V-belt drive
Max Rip Right/Left: 25" / 8" (48" right w/optional rails)
Max Depth of Cut: 3-1/8" (90°), 2-1/8" (45°)
Table: 40-1/8" × 27", 1-3/4" thick
Fence: Front/rear locking, 30" × 2" × 3-1/2"
Dust Port: 4"
Construction: Cast iron table and wings, pre-formed steel cabinet
Warranty: 1 Year