Important Disclaimer: This article references a model that is no longer in production. Please note that the availability of replacement parts or discussed accessories is not guaranteed.
1. What type of motor does the G5850 Planer use?
The G5850 is powered by a 1 HP single-phase TEFC capacitor-start induction motor running at 3450 RPM. It uses a belt drive for smooth power transfer and features sealed, permanently lubricated bearings for low maintenance.
2. What are the electrical requirements for the G5850?
This planer operates on 220V, single-phase, 60 Hz power. It draws 7.5 amps and requires a 15A circuit. The machine includes a 5-15 plug and features a toggle safety switch with a removable key.
3. What is the cutting capacity of the G5850?
- Maximum cut width: 12 inches
- Maximum cut height: 6 inches
- Maximum stock thickness: 6 inches
- Minimum stock thickness: 1/8 inch
- Minimum stock length: 8 inches
- Feed rate: 26 feet per minute (FPM)
- Maximum cut depth (full width): 1/16 inch
- Maximum cut depth (6" board): 1/8 inch
4. What type of cutterhead does the G5850 have?
The G5850 features a 3-knife straight cutterhead. The knives are HSS, reversible, and indexed for easy setup without a jig. Each knife measures 13" long, 1/2" wide, and 1/16" thick, with clamp block adjustment for precise alignment.
5. How fast does the cutterhead spin?
The cutterhead runs at 9,000 RPM, producing up to 27,000 cuts per minute, depending on feed rate and knife setup.
6. What material is the table made of?
The G5850 has a stainless steel table measuring 33-1/4" long by 13" wide. It includes rubber infeed and outfeed rollers and table/headstock locks for stability.
7. Does the G5850 include a dust collection system?
Yes, it has a built-in dust collection system with a 2-1/2" port, allowing connection to a shop dust collector for efficient chip removal.
8. How safe is the G5850 to operate?
Safety features include:
- Toggle safety switch with removable key
- Table/headstock locks
- Rubberized feed rollers
Always wear eye and ear protection due to the 102 dB sound rating.
9. How portable is the G5850?
The planer has grab handles and a lightweight aluminum body for easy repositioning in your shop.
10. How long does it take to assemble the G5850?
Assembly and setup take approximately 10 minutes.
11. What is the warranty on the G5850 Planer?
The G5850 comes with a 1-year warranty covering parts and manufacturing defects.
12. Where is the G5850 manufactured?
This planer is produced in an ISO 9001-certified factory and is NRTL-certified for safety.
13. Can I run moulding knives in my G5850 Planer?
No. The G5850 does not support moulding knives due to clearance and infeed roller limitations.
14. What type of feed rollers does it have?
- Infeed roller: Steel segmented
- Outfeed roller: Solid smooth steel
15. What size circuit breaker do I need?
A 30 Amp circuit breaker is recommended.
16. How can I connect the 5" dust port to a 4" hose?
- Use a 5" to 4" stovepipe reducer (available at most hardware stores)
- Then connect your 4" hose to the dust collector
17. What are the CFM requirements for dust collection?
For runs 10 feet or less, a dust collector with 450 CFM may work. However, bigger is always better for performance.
18. How are the planer knives adjusted?
Knives are adjusted using jackscrews, but adjustment springs are also included for those who prefer that method.
19. How many knives are in the cutterhead?
The cutterhead contains three knives.
20. What is the feed rate of this planer?
The feed rate is 24 feet per minute.