The G0766 lathe features a 3 HP, 3-phase TEFC induction motor with a Delta VFD-MS inverter for variable-speed control and single-phase power compatibility. It offers a 22-inch swing over bed, 42-inch distance between centers, and spindle speeds from 100 to 3200 RPM. Constructed from cast iron with a rotating headstock and digital spindle readout, it includes various accessories and a 1-year warranty.
What type of motor is used in the G0766?
The lathe is powered by a 3 HP, 3-phase TEFC induction motor running at 1720 RPM. It uses a belt drive system and includes sealed, permanently lubricated bearings for long-lasting performance.
Does the G0766 lathe include a Variable Frequency Drive (VFD)?
Yes. The G0766 is equipped with a Delta VFD-MS inverter (3 HP), which provides electronic variable-speed control and smooth operation.
The VFD allows the machine to run on single-phase input power, even though the motor itself is three-phase, greatly expanding compatibility with common shop electrical systems.
What are the electrical requirements for the G0766 lathe?
The G0766 requires 240V, single-phase, 60 Hz power.
- Full-load current: 13.5A
- Recommended minimum circuit size: 20A
- Power cord: 6 ft, 12 AWG
- Plug type: NEMA 6-20 (plug-and-play for most 240V shop outlets)
Because the machine uses a VFD, input voltage flexibility is built into the system. As long as your supply voltage falls within the acceptable range (generally 198V–242V, depending on nominal voltage), the lathe will operate safely and reliably on 208V, 220V, or 240V power.
✅ Important: Always verify your incoming power meets the machine’s specified input requirements. For VFD-equipped machines like the G0766, the input power rating—not the motor nameplate—determines compatibility.
What is the swing capacity and distance between centers?
- Swing over bed: 22 inches
- Swing over tool rest base: 18 inches
- Distance between centers: 42 inches
- Max tool rest to spindle center: 8 inches
This makes the G0766 ideal for turning large bowls, platters, and long spindles.
What is the spindle speed range?
The G0766 offers variable spindle speeds from 100 to 3200 RPM, with two optimized ranges:
- Low speed: 100–1200 RPM
- High speed: 330–3200 RPM
A digital spindle-speed indicator provides real-time feedback for precision turning.
What spindle specifications should I know?
- Spindle taper: MT#2
- Spindle thread: 1-1/4" x 8 TPI, right-hand
- Spindle bore: 3/8 inch
- Indexing: 10° and 30° increments with 24 total indexes
- Forward/reverse spindle control is included for added versatility.
What accessories come with the G0766 lathe?
Included accessories:
- 6" faceplate
- Spur center
- Cupped live center
- Knock-out tool
- Tool rest
- Indexing pin
What is the construction quality of the G0766?
The lathe is built with cast iron throughout the bed, frame, stand, headstock, and tailstock, ensuring maximum stability and vibration dampening. It features a durable enamel finish.
What are the tool rest and tailstock specifications?
- Tool rest width: 14 inches
- Tool rest post diameter: 1 inch
- Tool rest post length: 2-1/4 inches
- Tool rest base height: 2 inches
- Tailstock taper: MT#2
- Tailstock barrel travel: 4-1/4 inches
- Included tailstock center: Live
What are some standout features of the G0766?
- Electronic variable-speed control
- Digital spindle-speed readout
- Forward/reverse spindle control
- Rotating headstock (180°)
- Cam-lock adjustments for quick repositioning
- ISO 9001 certified factory
- NRTL certified for safety compliance
What is the warranty and setup time?
The G0766 comes with a 1-year warranty and takes approximately 1 hour to assemble and set up. The serial number is located on the ID label for registration and support.