What are the main features of the G0817?
The G0817 is a 14" resaw capacity bandsaw with a 2 HP motor capable of 110V or 220V single-phase operation. Key features include:
14" resaw capacity and 13-1/2" max cutting width
Solid one-piece reinforced steel frame
Cast-iron fence with 2-position, 6" tall resaw fence
Handwheel-operated rack-and-pinion upper guide post
Lever-action table tilt with rack-and-pinion adjustment
Modular blade guide system for quick changeovers
Foot-operated brake system for safety
Dual 4" dust ports
Heavy-duty cast-iron wheels and table trunnions
Built-in storage for extra blades and miter gauge
What is the origin and warranty of this bandsaw?
Country of Origin: Taiwan
Warranty: 1 year from the date of purchase
How long does it take to assemble and set up?
Approximately 1 hour.
Does the bandsaw include storage?
Yes, it has built-in storage for extra blades and the miter gauge when not in use.
Electrical & Motor
What voltage and circuit are required?
Voltage: 110V or 220V single-phase, 60Hz (prewired 110V)
Full-load current: 19A at 110V, 9.5A at 220V
Minimum circuit size: 20A at 110V, 15A at 220V
Does the bandsaw have overload protection?
Yes, it includes a control panel with magnetic switch protection and lockout key.
What are the motor specifications?
Horsepower: 2 HP
Speed: 1720 RPM
Type: TEFC Capacitor-Start Induction
Power transfer: Belt drive
Bearings: Shielded & permanently lubricated
Can this machine run on a 20 amp circuit?
Yes, at 110V, a 20A circuit meets the minimum requirement. At 220V, a 15A circuit is sufficient.
Blade & Cutter Information
What blade comes with the saw?
The bandsaw comes with a P0817023 blade, 120" x 3/8", 6 TPI, hook pattern.
What is the maximum blade width?
The saw supports blades 1/8" to 3/4" wide.
Does the saw have blade guide bearings below the table?
Yes, blade guide bearings are located below the bed.
Is the resaw bar compatible with the G0817 resaw fence?
T1213 Drift Bar: Yes, requires alignment and drilling a hole in the aluminum fence face.
T1194: Yes, replaces the resaw fence with a pre-drilled hole, allowing flexibility to have two fence options.
Can this saw be purchased with the 220V Kit installed from the factory?
This option is under evaluation. Contact Product Support for assistance with proper wiring during conversion.
Table & Fence
What are the table specifications?
Length: 21-3/4"
Width: 16-1/8"
Thickness: 1-1/2"
Tilt: Left 5°, Right 45° via lever-action adjustment
What type of fence does this bandsaw use?
The saw has a cast-iron fence with a 2-position extruded aluminum resaw fence. The fence is adjustable for blade lead.
Is a miter gauge included?
Yes, a miter gauge with 0–60° range is included.
Can the table be tilted easily?
Yes, the lever-action rack-and-pinion table tilt allows quick adjustment from left 5° to right 45°.
Operation & Performance
What is the maximum cutting width?
Left of blade: 13-1/2"
Left of blade with fence: 12"
What is the maximum cutting height (resaw height)?
14"
What is the blade speed?
2820 FPM
Does the bandsaw have a foot brake?
Yes, the foot brake also acts as a safety device, bringing the saw to a quick stop.
Can this saw be stabilized on a mobile base?
Yes, but it is top-heavy. Recommendations: square the mobile base, secure the saw to plywood within the base, and position the wheels correctly.
Dust Collection
How many dust ports does the saw have?
Two 4" dust ports.
Can I connect a 4" Y-connector to use one hose for both ports?
Yes, connect the bandsaw dust port to a single 4" hose, securing with hose clamps.